Here’s the setup and configuration for a Linksys PAP2t for VoIP. Manual for basic configuration and management. Linksys is a registered trademark or trademark of Cisco. Systems, Inc. and/or its affiliates in the U.S. and . Linksys PAP2, PAP2-NA, PAP2T-NA BYOD VoIP SIP Setup and Configuration guide with Internet Phone Service Provider.

Author: Gacage Negal
Country: Montserrat
Language: English (Spanish)
Genre: Sex
Published (Last): 21 September 2016
Pages: 425
PDF File Size: 14.2 Mb
ePub File Size: 12.49 Mb
ISBN: 381-5-75884-265-3
Downloads: 21974
Price: Free* [*Free Regsitration Required]
Uploader: Vudolar

Home How it works?

For more information on the Cisco range of IP phones, please visit the Cisco phones product website. Are you looking for a quote for: Please refer to our Privacy Policy or Contact Us for more details. We do not support G. Typically G, which is an un-compressed codec would be the choice, but to conserve on bandwidth you might change Line 1 “Preferred Codec” to Ga.

Just plug it into your home Router or Gateway and use the two standard telephone jacks to connect your existing phones. Except where otherwise noted, content on this wiki is licensed under the following license: How many phones do you have? This is provided in your welcome email. Make the following changes on LINE 1 you have to click on advanced view to see these options.

Click on the “Admin Login” button near the top right side of the screen, then click on the “Line 1” tab.

How to configure a Linksys PAP2t for VoIP.

If you are experiencing issues with voice hearing the caller or the caller hearing you and so onthen ensure you have followed Step 5 above. See this page for further information. If everything appears to be correct, the problem may be your firewall.


Each phone jack operates independently, with separate phone service and configurtion numbers – like having two phone lines. Use the above as an example as your system administrator may be able to provide you with your company’s internal NTP servers.

If you get one-way audio, you are probably behind NAT. Your router’s firewall also known as NAT is blocking certain operations of the VoIP telephone adapter or some of the settings of the adapter is not entered correctly.

How to Set Up the Linksys PAP2T Telephone Adapter [SureVoIP Support]

Device will now get settings remotely from our servers. To do this, you need to pick up the phone attached to the Line configguration jack and dial: I understand that I can withdraw my consent at anytime. The following instructions are typical instructions for line 1. If the phone fails to login, please take the time to double check your configuration as above.

Enter your full name, this will show up as part of your caller ID. Once the page has loaded, linlsys Admin Login then press advanced.

Linksys PAP2T VoIP Adaptor Setup

You are requesting a quote and other information regarding your telecommunications needs. If the Status page shows timeout, check over your firewall settings. I agree to receive quotes, configuratio and other information from voipmechanic. You must first determine what IP address it received.

Linksys pap2t voice setup

You can only do this for one line. The Preferred codec drop down box has several choices. If you are having issues dialling out, go to Regional tab and at the Vertical Service Activation Codes section remove all the feature codes.


More Than 6 Months. What is your data connection? These are optional settings, but are highly recommended to get the best experience out of your phone. Fill out the form below: Each phone port operates independently with separate phone service and their own phone numbers, line 1 and line 2.

Under Subscriber Information put your name into Display Name. Using compression like G does is processor intensive and both these ATA models do not have a capacity to handle simultaneous G calls. Unplug your device from the power and plug back after 5 seconds to reboot the device. If registration is failing, check over the settings entered above. Less Than 1 Month.

Search Help My Account. Click on the “Admin Login” button near the top right side of the screen, then click on the “Line 1” tab.

To save bandwidth, you can change Line 1 “Preferred Codec” to Ga.

In most cases you will need only modify a few parameters from the normal factory default settings. Please check our VoIP device troubleshooter. If you find dialling international numbers causes beeping before you finish dialling, then under Regional tab and under Control Timer Values sec section increase Interdigit Long Timer and Interdigit Short Timer.

What is cknfiguration buying time frame? Set Locale to en- GB.