CCNP SWITCH 6.0 INSTRUCTOR LAB MANUAL PDF

CCNP SWITCH 6.0 INSTRUCTOR LAB MANUAL PDF

CCNP SWITCH 6 – BitRadius. Instructor Lab Manual Book everyone. Download file Free Book PDF Ccnp Switch Instructor Lab Manual at. CCNP: Implementing Secure Converged Wide-area Networks v – Lab Copyright © Ensure that the switch is set up so that both the router and host are in the same. VLAN. .. Figure Internet Explorer Security Alert Prompt. ccnp switch instructor lab pdf. CCNP SWITCH Instructor Lab Manual. This document is exclusive property of Cisco Systems, Inc.

Author: Nikogor Vot
Country: United Arab Emirates
Language: English (Spanish)
Genre: History
Published (Last): 17 June 2015
Pages: 332
PDF File Size: 9.32 Mb
ePub File Size: 3.16 Mb
ISBN: 469-3-59648-524-7
Downloads: 71995
Price: Free* [*Free Regsitration Required]
Uploader: Dat

Ccnp Tshoot Lab Manual Configuration Files – downloadsoftspecialists

Use the show vtp status command on any switch. In this instductor, the default operation of IEEE The default mode on a or is dynamic auto; the default mode on a or is dynamic desirable. If a foreign or rogue switch is maliciously or accidentally added to the network, the STP topology could be changed if the new switch has a lower BID than the current root bridge.

You can use other switches such as a or and Cisco IOS Software versions if they have comparable capabilities and features. IP adj out of Vlan1, addr VLAN information is not propagated until a domain name is specified and trunks are set up between the devices. DLS1 config ip sla schedule 1 life forever start-time now DLS1 config ip sla schedule 2 life forever start-time now DLS1 config ip sla schedule 3 life forever start-time now DLS1 config ip sla schedule 4 life forever start-time now Step FOC Power supply serial number: Blocking can occur on the access layer switch or the distribution layer switch.

  JRPRINTSERVICEEXPORTER PRINT PDF

CCNP SWITCH Lab Manual, 2nd Edition

To choose which port becomes the root on a non-root switch when faced manuap equal-cost redundant root paths via the same neighbor, the switch looks at the port priorities first. ALS1 configure terminal Enter configuration commands, one per line. Verify the auto QoS configuration at the access layer using the show mls qos interface interface-type interface-number and show run commands. This lab assumes that you have completed LabClearing a Switch.

The virtual gateway IP address is typically a fictitious, unassigned IP address, such as the address we are using here, to be used by Layer 3 Security and Mobility managers. The trunks are being statically set to Design the addressing scheme using the address space Use the show vlan private-vlan command and note that the ports configured are currently associated with these VLANs.

You are finished clearing both the configuration and VLANs from the swittch. Resetting system with new configuration The following is a sample configuration for the trunks and EtherChannel from DLS1 to the other three switches.

Ping from Host A to Host B. The commands are shown isntructor DLS1 only. Display the spanning tree information for DLS2 again. Configure a Layer 3 EtherChannel. In dynamic networks, fast-switching cache entries are frequently invalidated because of routing changes. Configure the switch hostnames as shown in the topology.

Configure all inter-switch links statically instrructor EtherChannel is used for these trunks. Enable QoS on all switches involved in the scenario. You plan to test the configurations in a lab environment before placing them into production.

  BROTHER MFC 255CW MANUAL PDF

To change the port cost on a per-VLAN basis, use the interface-level command spanning-tree vlan number cost cost, rather than the command spanning-tree cost cost, which applies to all VLANs. The output from switch ALS1 is shown as an example. If costs were equal, the tie was broken first by the lowest sender BID of the BPDU, then by the lowest sending port priority and last by the lowest sending port number.

To maintain an efficient STP topology, the root bridge must remain predictable. In this lab, you will see what happens when the default spanning tree behavior is modified. Notice that the VTP mode is server mode. Background The current network equipment includes a distribution layer switch and two access layer switches. You can change the native VLAN to something other than VLAN 1 on trunk ports using the switchport trunk native vlan vlan-id command in interface configuration mode.

This step might take a few minutes, because the switch needs time to reload.

Sign In We’re sorry! It is possible that a switch could be accidentally or maliciously added to those ports. Notice that the output is identical to show spanning-tree mst configuration.

The output should be similar to the following output.