BS EN ISO Safety of machinery – Basic concepts, general principles for design – Part 1: Basic terminology, methodology. [Note that EN ISO and EN have both been superseded by EN ISO – Ed, 31 December ]. EN ISO IEC – 1. Electrical. Equipment. BS EN Safety of machinery. Rules for drafting and. Presentation of safety standards. BS ISO
|Published (Last):||25 July 2008|
|PDF File Size:||5.99 Mb|
|ePub File Size:||10.7 Mb|
|Price:||Free* [*Free Regsitration Required]|
The elements of risk are shown in Figure 3.
1210-01 NOTE 1 This stage is the only one at which hazards can be eliminated, thus avoiding the need for additional protective measures such as safeguarding or complementary protective measures.
When considering these effects, risk estimation shall, as far as practicable, be based on appropriate recognized data. 12010-1 information for use shall prescribe regular checking of warning devices. Document Status Indicators The Green document status indicator indicates that the document is: These principles are based on knowledge and experience of the design, use, incidents, accidents and risks associated with machinery. Looking in detail at Part 1, there are three main clauses in addition to the scope and normative references.
Consideration should be given to presenting information in tabular form where this will aid understanding. For each type of hazard or group of hazards, some potential consequences can be related to several origins of hazard. The designer’s attention is particularly drawn to following ergonomic aspects of machine design.
Please download Chrome or Firefox or view our browser tips. For some special machinery other protective measures can be appropriate.
Safety of machinery: EN ISO 12100-1 and EN ISO 12100-2
YES At each step of the iterative process: NOTE Also improved are the performance and reliability of operation and hence the reduction in the probability of errors at all stages of machine use. The concept of safety of machinery considers the ability of a machine to perform its intended function s during its life cycle where risk has been adequately reduced.
Hazardous event Contact with rough surfaces Contact with sharp edges and corners, protruding vs Contact with moving parts Contact with rotating open ends 6. When a type-C standard deviates from one or more technical provisions dealt with by this International Standard or by a type-B standard, the type-C standard takes precedence.
When the application requires reprogramming by the user, the access to the software dealing with een functions should be restricted for example, by locks or passwords for the authorized persons.
Yes No — — fixed guards see 6. The primary action for stopping or slowing down should be performed by removal or reduction of voltage or iiso pressure, or — if binary logic elements are considered — by passage from state 1 to state 0 where state 1 represents the highest energy state.
BS EN ISO _百度文库
The main task of technical committees is to prepare International Standards. Your basket is empty. As shown in Bss 1, the adequacy of the risk reduction shall be determined after applying each of the three steps of risk reduction described in Clause 6. This International Standard distinguishes the residual risk after protective measures have been implemented by the designer, the residual risk remaining after all protective measures have been implemented.
Safeguarding and complementary protective measures Step 3: Take the smart route to manage medical device compliance. Minimum gaps to avoid crushing of parts of the human body. International organizations, governmental and non-governmental, in liaison with ISO, also ne part in the work.
Again there may be more recent versions of the document. Break-up 1210-1 operation 6. Guidance is given on the documentation and verification of the risk assessment and risk reduction process.
When determining these elements, it is necessary to take into account the aspects given in 5. Factors to be taken into account when estimating the occurrence of a hazardous event are, among others, a b c d reliability and other statistical data, accident history, history of damage to health, and comparison of risks see 5.
Mechanization ios be achieved by, for example, feeding slides, push-rods and hand-operated indexing tables. One of the advantages of modern safety-related control systems is that they isoo assist with reducing cycle times if, for example, sensitive protective equipment is used to initiate the cycle when the operator has cleared the hazardous area. Once active operation of the emergency stop device has ceased following an emergency stop command, the effect of this command shall be sustained until it is reset.
You may find similar items within these bz by selecting from the choices below:. As the need for frequency of access increases, this inevitably leads to the fixed guard not being replaced.
This International Standard is a type-A standard. More details for the design and selection of electrical components and elements to achieve the emergency stop function are provided in IEC See Figure 4 and ISO